828 research outputs found
Inhibited Shaped Charge Launcher Testing of Spacecraft Shield Designs
This report describes a test program in which several orbital debris shield designs were impact tested using the inhibited shaped charge launcher facility at Southwest Research Institute. This facility enables researchers to study the impact of one-gram aluminum projectiles on various shielding designs at velocities above 11 km/s. A total of twenty tests were conducted on targets provided by NASA-MSFC. This report discusses in detail the shield design, the projectile parameters and the test configuration used for each test. A brief discussion of the target damage is provided, as the detailed analysis of the target response will be done by NASA-MSFC
Inhibited Shaped Charge Launcher Testing of Spacecraft Shield Designs
This report describes a test program in which several orbital debris shield designs were impact tested using the inhibited shaped charge launcher facility at Southwest Research Institute. This facility enables researchers to study the impact of one-gram aluminum projectiles on various shielding designs at velocities above 11 km/s. A total of twenty tests were conducted on targets provided by NASA-MSFC. This report discusses in detail the shield design, the projectile parameters and the test configuration used for each test. A brief discussion of the target damage is provided, as the detailed analysis of the target response will be done by NASA-MSFC
Anchored Bulkhead Failure on the Arabian Gulf
A 1500-m long anchored bulkhead with a height of 20m exhibited a localized failure in the form of broken and overstressed anchors several months after construction. The wall had not yet been subjected to its full design loadings. The soil conditions in the failure area differ from those occurring along the rest of the quay wall by the presence of a very soft silt/clay layer, and during construction the wall had been strengthened in this area. Post-failure analysis of the anchored bulkhead indicated that the primary cause of the failure was overly optimistic design assumptions for the strength of the silt/clay layer and mobilization of passive pressure. The effects of certain construction methods employed and the settlement of the silt/clay were contributing factors in the failure. A relieving platform constructed one year after the failure was designed for the original undrained strength of the silt/clay, without taking into account the effects of soil consolidation and strength gains which had occurred
Feasibility study for a Scanning Celestial Attitude Determination System /SCADS/ for three axis attitude determination at a Command and Data Acquisition /CDA/ station Final report
Scanning Celestial Attitude Determination System /SCADS/ for three axis attitude determination at Command and Data Acquisition /CDA/ statio
Rubber friction on wet and dry road surfaces: the sealing effect
Rubber friction on wet rough substrates at low velocities is typically 20-30%
smaller than for the corresponding dry surfaces. We show that this cannot be
due to hydrodynamics and propose a novel explanation based on a sealing effect
exerted by rubber on substrate "pools" filled with water. Water effectively
smoothens the substrate, reducing the major friction contribution due to
induced viscoelastic deformations of the rubber by surface asperities. The
theory is illustrated with applications related to tire-road friction.Comment: Format Revtex 4; 8 pages, 11 figures (no color); Published on Phys.
Rev. B (http://link.aps.org/abstract/PRB/v71/e035428); previous work on the
same topic: cond-mat/041204
Rubber friction on (apparently) smooth lubricated surfaces
We study rubber sliding friction on hard lubricated surfaces. We show that
even if the hard surface appears smooth to the naked eye, it may exhibit short
wavelength roughness, which may give the dominant contribution to rubber
friction. That is, the observed sliding friction is mainly due to the
viscoelastic deformations of the rubber by the substrate surface asperities.
The presented results are of great importance for rubber sealing and other
rubber applications involving (apparently) smooth surfaces.Comment: 7 pages, 15 figure
Rubber friction on smooth surfaces
We study the sliding friction for viscoelastic solids, e.g., rubber, on hard
flat substrate surfaces. We consider first the fluctuating shear stress inside
a viscoelastic solid which results from the thermal motion of the atoms or
molecules in the solid. At the nanoscale the thermal fluctuations are very
strong and give rise to stress fluctuations in the MPa-range, which is similar
to the depinning stresses which typically occur at solid-rubber interfaces,
indicating the crucial importance of thermal fluctuations for rubber friction
on smooth surfaces. We develop a detailed model which takes into account the
influence of thermal fluctuations on the depinning of small contact patches
(stress domains) at the rubber-substrate interface. The theory predicts that
the velocity dependence of the macroscopic shear stress has a bell-shaped f
orm, and that the low-velocity side exhibits the same temperature dependence as
the bulk viscoelastic modulus, in qualitative agreement with experimental data.
Finally, we discuss the influence of small-amplitude substrate roughness on
rubber sliding friction.Comment: 14 pages, 16 figure
Blending HF Radar and Model Velocities in Monterey Bay Through Normal Mode Analysis
Nowcasts of the surface velocity field in Monterey Bay are made for the period August 1-9, 1994, using HF radar observations blended with results from a primitive equation model. A spectral method called normal mode analysis was used. Objective spatial and temporal filtering were performed, and stream function, velocity potential, relative vorticity, and horizontal divergence were calculated over the domain. This type of nowcasting permits global spectral analysis of mode amplitudes, calculation of enstrophy, and additional analyses using tools like empirical orthogonal functions. The nowcasts reported here include open boundary flow information from the numerical model. Nowcasts using no open boundary flow information, however, still provide excellent results for locations within the observation footprint. This method, then, is useful for filtering high-resolution data like HF radar observations, even when open boundary flow information is unavailable. Also, since the nowcast velocity gradient fields were much less noisy than the observations, this may be an effective method for preconditioning high-resolution observation sets for assimilation into a numerical model. Copyright 2000 by the American Geophysical Union
Rubber friction: role of the flash temperature
When a rubber block is sliding on a hard rough substrate, the substrate
asperities will exert time-dependent deformations of the rubber surface
resulting in viscoelastic energy dissipation in the rubber, which gives a
contribution to the sliding friction. Most surfaces of solids have roughness on
many different length scales, and when calculating the friction force it is
necessary to include the viscoelastic deformations on all length scales. The
energy dissipation will result in local heating of the rubber. Since the
viscoelastic properties of rubber-like materials are extremely strongly
temperature dependent, it is necessary to include the local temperature
increase in the analysis. At very low sliding velocity the temperature increase
is negligible because of heat diffusion, but already for velocities of order
0.01 m/s the local heating may be very important. Here I study the influence of
the local heating on the rubber friction, and I show that in a typical case the
temperature increase results in a decrease in rubber friction with increasing
sliding velocity for v > 0.01 m/s. This may result in stick-slip instabilities,
and is of crucial importance in many practical applications, e.g., for the
tire-road friction, and in particular for ABS-breaking systems.Comment: 22 pages, 27 figure
- …